Your cart is currently empty
The performance of an industrial dust filter is not determined solely by the filter fibres used. The surface treatment, coating or membrane layer of the filter medium also has a significant impact on filtration efficiency, dust release, pressure drop and service life.
SOLANA supplies filter media with various treatments and coatings for use in filter pockets and multi-pocket filter bags, filter sleeves and filter bags and other industrial dust filters.
Below you will find an overview of the most commonly used treatments and coatings for industrial dust filtration, their properties and typical applications.
Industrial dust filters are exposed to a wide range of operating conditions, including high temperatures, moisture, sticky or abrasive dust particles, chemicals and electrostatic charging.
Depending on the application, a suitable treatment can contribute to:
The right treatment can therefore help reduce maintenance costs and the total cost of ownership of the filtration system.
However, not every treatment is suitable for every filter material. The selection must always take into account the filter fibre, dust characteristics, operating conditions and cleaning method.
|
Treatment |
Main function |
Typical applications |
|---|---|---|
|
Heat setting |
Improved shape and dimensional stability |
Synthetic filter media, thermal stress |
|
Singeing |
Removal of protruding surface fibres |
Improved dust release, general dust filtration |
|
Calendering and smooth finishes |
Smoothing and densification of the filter surface |
Fine dust, sticky or difficult-to-release dust |
|
Hydrophobic and oleophobic treatment |
Water and oil repellency |
Humid, oily or sticky dust particles |
|
Antistatic filter media |
Dissipation or reduction of electrostatic charge |
Combustible dust, applications with explosion risks |
|
Spark-resistant or flame-retardant treatment |
Reduced ignition susceptibility or damage from hot particles |
Metalworking, processes involving sparks |
|
PTFE coating or impregnation |
Improved surface properties and chemical resistance |
Chemically demanding processes, sticky dust |
|
Microfibre finish |
Finer fibre structure for improved dust collection |
Fine dust, demanding filtration applications |
|
ePTFE membrane |
Surface filtration using a microporous membrane |
Fine dust, low emission requirements |
The final properties depend on the combination of filter material, treatment and filter construction.
Heat setting is a thermal treatment in which the filter material is heated under controlled conditions to stabilise its fibre structure and dimensional stability.
For suitable synthetic filter media, this treatment reduces the tendency to shrink or deform during operation.
Advantages
Typical applications
Heat setting is widely used for synthetic needle felts in industrial dust filters.
The treatment does not automatically increase the maximum permissible operating temperature of the filter fibre.
Singeing is a controlled thermal treatment used to remove protruding fibre ends from the surface of the filter medium.
This creates a more uniform surface, reducing the tendency of dust particles to become mechanically trapped between protruding fibres.
Advantages
Typical applications
Singeing is commonly applied to needle felts used in general industrial dust filtration.
The treatment can be combined with calendering or other surface finishes.
During calendering, the filter material passes between rollers under pressure, sometimes combined with heat. This produces a smoother surface and may locally densify the filter structure.
Depending on the technique and treatment intensity, various finishes are possible, including glazed and eggshell finishes.
Advantages
Limitations
A highly densified surface may reduce air permeability. The appropriate finish must therefore be selected according to the required filtration performance and permissible pressure drop.
Typical applications
Hydrophobic and oleophobic treatments are used to reduce wetting of the filter medium by water or oil.
A hydrophobic treatment makes the surface water-repellent, while an oleophobic treatment reduces wetting and adhesion by oily substances.
Both properties can be combined in a single treatment.
Advantages
Limitations
These treatments do not necessarily make a filter medium waterproof or suitable for continuous condensation. In humid processes, fibre selection, temperature and the dew point of the process gas remain important considerations.
Typical applications
During industrial dust filtration, the movement and friction of dust particles can generate electrostatic charges.
When combustible dust is present, uncontrolled electrostatic discharge may create an ignition risk.
For certain applications, electrically conductive or electrostatically dissipative filter media are therefore used.
These properties can be achieved through:
Advantages
Typical applications
Important information about ATEX
An antistatic filter medium alone does not automatically make a filtration system suitable for operation in an ATEX environment.
The required electrical properties, earthing arrangements and additional safety measures must be determined through an explosion risk assessment of the entire installation.
For more information, visit our page on antistatic filter media.
In certain industrial processes, sparks, glowing particles or hot dust particles may be present in the extracted air.
Depending on the application, filter media can be manufactured with special treatments designed to increase resistance to spark exposure or reduce flammability.
These include flame-retardant impregnations and specialised protective surface coatings.
Advantages
Limitations
A spark-resistant or flame-retardant treatment does not make a filter medium non-combustible and does not guarantee that incoming sparks will be extinguished.
Applications involving spark hazards may require additional protective measures, such as spark detection, spark extinguishing, spark separation or other fire and explosion protection systems.
Typical applications
The appropriate filter construction and safety measures must always be selected in relation to the entire installation.
PTFE (polytetrafluoroethylene) is a polymer characterised by exceptional chemical resistance and low surface energy.
PTFE can be used as a filter fibre, but it can also be applied as a coating or impregnation to certain other filter media.
Depending on the application, PTFE treatment can improve the surface properties of the filter medium.
Advantages
Limitations
Performance depends on the type of coating, the amount of PTFE applied and the underlying filter material.
A PTFE coating does not automatically provide the same chemical or thermal resistance as a filter medium manufactured entirely from PTFE fibres.
Typical applications
A PTFE coating or impregnation should not be confused with a laminated ePTFE membrane.
Filter media containing microfibres use particularly fine fibres to create a finer filtration structure.
These fibres may form part of the filter medium itself or be incorporated into a specially designed fine surface layer.
A microfibre finish is therefore primarily a modification of the fibre structure rather than a conventional chemical coating.
Advantages
Limitations
Actual collection efficiency depends on the fibre structure, filter medium, dust characteristics and operating conditions.
The presence of microfibres alone does not guarantee a specific filtration efficiency or emission level.
Typical applications
Membrane lamination involves applying a thin, microporous membrane made from expanded PTFE (ePTFE) to a suitable supporting filter material.
The membrane forms a fine-pored surface layer that promotes the collection of dust particles at the filter surface.
This helps limit the penetration of dust particles into the deeper structure of the filter medium.
Advantages
Limitations
The membrane structure, supporting material and filter construction influence air permeability, pressure drop and mechanical durability.
An ePTFE membrane does not automatically increase the temperature resistance or chemical resistance of the underlying filter material.
Typical applications
The most suitable treatment depends on the dust characteristics, filter material and operating conditions.
The following table provides general guidance on possible solutions.
|
Operating conditions |
Possible treatments or filter constructions |
|---|---|
|
General industrial dust filtration |
Heat setting, singeing, calendering |
|
Sticky or difficult-to-release dust |
Smooth surface finish, hydrophobic or oleophobic treatment, suitable PTFE coating |
|
Humid or oily process air |
Hydrophobic or oleophobic treatment |
|
Fine dust particles and low emission requirements |
Microfibre finish, ePTFE membrane |
|
Chemically demanding processes |
Suitable PTFE treatment combined with a chemically resistant filter medium |
|
Electrostatic charging and explosion risks |
Conductive or antistatic filter media selected according to the ATEX risk assessment |
|
Spark exposure or hot particles |
Suitable spark-resistant or flame-retardant filter media combined with appropriate installation protection |
This table is intended as general guidance. Not all treatments are compatible with every fibre type or filter construction.
The final selection must also take into account operating temperature, chemical exposure, air permeability, cleaning method and required service life.
The selection of filter media begins with the properties of the fibres used. Polyester, polypropylene, PPS, meta-aramid, polyimide, PTFE and fibreglass differ in temperature resistance, chemical resistance and mechanical properties.
A coating or surface treatment may improve certain performance characteristics, but it does not automatically overcome the limitations of the underlying filter fibre.
Therefore, fibre selection, filter construction and surface treatment should always be considered together.
Read our knowledge page on properties of filter fibres for a comparison of the different filter materials.
A surface treatment modifies the properties or structure of the filter surface, for example through singeing or calendering.
A coating involves applying an additional layer or substance to or into the filter material to achieve specific properties. In practice, the two terms may partly overlap.
A PTFE coating or impregnation is applied to improve certain surface or chemical properties.
An ePTFE membrane is a separate microporous layer laminated onto the filter medium to improve surface filtration and the collection of fine dust particles.
The required properties of the filter medium depend on the explosion risk assessment, dust characteristics and installation.
Where electrostatic charging presents an ignition risk, an electrically conductive or dissipative filter medium may be necessary. Additional safety measures may also be required.
No. A suitable treatment may extend service life by reducing dust adhesion or improving filter cleaning.
However, an unsuitable treatment can negatively affect air permeability, cleanability or overall filter performance.
No. Suitability depends on the filter fibres used, filter construction, operating temperature and chemical and mechanical stress.
Not all coatings, membranes and surface treatments are compatible with every filter material.
The right combination of filter fibre, filter construction and surface treatment contributes to reliable filtration performance, efficient filter cleaning and a longer filter medium service life.
To help us recommend the most suitable solution, please provide the following information:
SOLANA can assist you in selecting suitable filter media, coatings and surface treatments for your industrial dust filtration application.
Contact us for technical advice or a quotation without obligation.