Your cart is currently empty
A shaker baghouse is an industrial dust collection system in which the filter bags are periodically cleaned by mechanical shaking. This movement dislodges the accumulated dust layer from the filter medium, allowing the filter bags to operate efficiently again.
In a conventional shaker baghouse, dust-laden air flows from the inside to the outside of the filter bags. Dust particles are retained on the inner surface of the filter medium, while the cleaned air passes through the bags and is discharged from the system.
SOLANA manufactures custom-made filter bags and filter sleeves for shaker baghouses, with filter materials, dimensions and finishes tailored to the specific installation.
A shaker baghouse combines normal filtration of dust-laden air with a periodic cleaning cycle in which the filter bags are mechanically shaken.
During normal operation in a conventional shaker baghouse, dust-laden air enters the inside of the filter bags and flows outwards through the filter medium.
The air passes through the filter material, while dust particles are retained on the inner surface. Over time, a layer of accumulated dust forms, commonly referred to as the dust cake.
The cleaned air then flows along the outside of the filter bags towards the outlet of the installation.
Because filtration takes place from the inside to the outside, the filtration surface of the filter medium generally faces inwards.
Correct orientation of the filter material is important for effective filtration and efficient removal of the accumulated dust layer.
As the dust cake becomes thicker, resistance to airflow increases.
To remove this dust layer, normal filtration in the relevant compartment of a conventional shaker system is temporarily interrupted.
The filter bags are then moved by a mechanically driven shaking system.
This movement is usually transferred to the filter bags through the mounting mechanism, causing the filter material to vibrate or shake.
The rapid movement and resulting forces break up the accumulated dust cake, allowing the dust to detach from the filter surface.
The dislodged dust falls into the lower section of the baghouse, where it is collected and discharged.
In installations with multiple compartments, filtration can generally continue in the remaining compartments while one compartment is being cleaned.
During normal filtration, the airflow holds the dust cake against the filter medium.
If this airflow were to continue during shaking, the dislodged dust could be pressed back against the filter surface.
Filtration in the relevant compartment is therefore usually interrupted temporarily, allowing dust particles to detach more easily and fall into the lower section of the baghouse.
This is an important difference compared with many pulse jet systems, where filter cleaning can take place while filtration continues.

Shaker baghouses often use long, cylindrical filter bags that are mechanically moved during the cleaning cycle.
The exact construction and mounting arrangement depend on the baghouse design and the type of shaking mechanism used.
Common finishes include:
The appropriate bottom construction depends on the design of the existing dust collection system.
In the shaker filter bags manufactured by SOLANA, a snap ring is frequently used at the top.
This fastening ring is incorporated into the upper cuff and forms part of the filter bag's mounting arrangement.
Other mounting designs are also possible, depending on the installation.
In shaker systems, it is particularly important that the filter bag is correctly secured and that the mechanical shaking movement is transferred as intended.
Because filter bags in shaker systems are subjected to repeated mechanical movement, mounting arrangements and finishing details play an important role.
When manufacturing replacement filters, several aspects must be considered:
Correct construction helps reduce premature wear or damage during cleaning cycles.
Needle felt is widely used in the shaker filter bags manufactured by SOLANA. Woven filter media are also possible, depending on the application and baghouse construction.
The choice of filter medium depends primarily on the characteristics of the dust, the operating conditions and the mechanical cleaning method.
Because the filter material is shaken regularly, it must not only provide the required filtration performance but also withstand repeated mechanical stress.
Important selection criteria include:
Depending on the operating conditions, different fibre materials, filter constructions and additional treatments may be used.
For more information on material selection, visit our knowledge pages on filter fibres, treatments and coatings and antistatic filter media.
Shaker baghouses are used in industrial dust filtration because of their relatively simple mechanical cleaning principle.
Correct material selection, construction and finishing are therefore important for reliable operation and satisfactory filter element service life.
The main difference between these three systems is the method used to clean the filter bags.
|
Feature |
Shaker |
Reverse air |
Pulse jet |
|---|---|---|---|
|
Cleaning method |
Mechanical shaking |
Reverse airflow |
Short compressed air pulses |
|
Typical filtration direction |
Inside to outside |
Inside to outside |
Outside to inside |
|
Filtration surface |
Inside of the bag |
Inside of the bag |
Outside of the bag |
|
Filter bag support and mounting |
Mounting suitable for mechanical shaking |
Often support rings along the length |
Usually an internal filter cage |
|
Cleaning during operation |
Usually one temporarily isolated compartment at a time |
Usually one temporarily isolated compartment at a time |
Often while filtration continues |
|
Typical filter media at SOLANA |
Mainly needle felt; woven media also possible |
Mainly needle felt; woven media also possible |
Mainly needle felt |
This comparison describes the typical construction and operating principles of the three systems. Different configurations may exist depending on the installation design.
For more information about the other cleaning methods, visit our knowledge pages on reverse air baghouses and pulse jet baghouses.
SOLANA operates its own production facilities for manufacturing custom-made industrial filter bags and filter sleeves.
We produce a wide range of constructions and finishes tailored to existing dust collection systems.
When manufacturing replacement filters, we take into account:
An existing filter bag can serve as a reference for determining the correct dimensions and finishing details.
Shaker refers to a mechanical cleaning method in which the filter bags are periodically shaken.
This movement breaks up the accumulated dust cake, allowing the dust to detach from the filter surface.
In a conventional shaker baghouse, dust-laden air generally flows from the inside to the outside of the filter bags.
Dust particles are retained on the inner surface of the filter medium. The filtration surface therefore usually faces inwards.
Yes. In a conventional shaker system, filtration in the compartment being cleaned is usually interrupted temporarily.
This allows the accumulated dust cake to detach more easily and fall into the lower section of the baghouse.
In installations with multiple compartments, filtration can continue in the remaining compartments.
No. Both the top and bottom of the filter bag can be finished in different ways.
In the designs manufactured by SOLANA, a snap ring is often used at the top. At the bottom, common finishes include round bottoms with an opening and flat bottoms with a fastening ring or fixing rod.
The correct construction depends on the baghouse design and the mechanical shaking system.
No. Needle felt is widely used in the shaker filter bags manufactured by SOLANA, but woven filter media are also possible.
The correct material depends on the dust characteristics, operating conditions, mechanical cleaning stress and required filtration performance.
In a shaker system, the dust cake is removed by mechanically shaking the filter bags.
In a reverse air system, the dust cake is dislodged by directing airflow through the filter medium in the opposite direction to normal filtration.
Both systems typically use inside-to-outside filtration in their conventional designs, but their cleaning methods and filter bag construction differ.
Yes. SOLANA manufactures custom-made filter bags and filter sleeves for a wide range of industrial shaker dust collection systems.
Dimensions, filter materials, mounting arrangements and finishing can be adapted to the existing installation.
When replacing filter bags in a shaker baghouse, it is important that both the filter medium and its construction are compatible with the existing installation.
To help us manufacture a suitable replacement filter, please provide:
SOLANA can assist you in selecting and manufacturing suitable replacement filter bags for your shaker dust collection system.
Contact us for technical advice or a quotation without obligation.